In case this helps anyone.
Linux version 2.6.31.4 (mcr@marajade.sandelman.ca) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 PREEMPT Mon Oct 19 15:36:45 EDT 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000005ff60000 (usable)
BIOS-e820: 000000005ff60000 - 000000005ff77000 (ACPI data)
BIOS-e820: 000000005ff77000 - 000000005ff79000 (ACPI NVS)
BIOS-e820: 000000005ff80000 - 0000000060000000 (reserved)
BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
DMI present.
last_pfn = 0x5ff60 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-DBFFF uncachable
DC000-DFFFF write-back
E0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask FC0000000 write-back
1 base 040000000 mask FE0000000 write-back
2 base 05FF80000 mask FFFF80000 uncachable
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
Warning only 895MB will be used.
Use a HIGHMEM enabled kernel.
initial memory mapped : 0 - 01c00000
init_memory_mapping: 0000000000000000-0000000037fe2000
0000000000 - 0000400000 page 4k
0000400000 - 0037c00000 page 2M
0037c00000 - 0037fe2000 page 4k
kernel direct mapping tables up to 37fe2000 @ 7000-c000
ACPI: RSDP 000f6d70 00024 (v02 IBM )
ACPI: XSDT 5ff6a672 0004C (v01 IBM TP-1R 00003230 LTP 00000000)
ACPI: FACP 5ff6a700 000F4 (v03 IBM TP-1R 00003230 IBM 00000001)
ACPI Warning: 32/64X length mismatch in Gpe1Block: 0/32 20090521 tbfadt-527
ACPI Warning: Optional field Gpe1Block has zero address or length: 000000000000102C/0 20090521 tbfadt-558
ACPI: DSDT 5ff6a8e7 0C530 (v01 IBM TP-1R 00003230 MSFT 0100000E)
ACPI: FACS 5ff78000 00040
ACPI: SSDT 5ff6a8b4 00033 (v01 IBM TP-1R 00003230 MSFT 0100000E)
ACPI: ECDT 5ff76e17 00052 (v01 IBM TP-1R 00003230 IBM 00000001)
ACPI: TCPA 5ff76e69 00032 (v01 IBM TP-1R 00003230 PTL 00000001)
ACPI: BOOT 5ff76fd8 00028 (v01 IBM TP-1R 00003230 LTP 00000001)
895MB LOWMEM available.
mapped low ram: 0 - 37fe2000
low ram: 0 - 37fe2000
node 0 low ram: 00000000 - 37fe2000
node 0 bootmap 00008000 - 0000f000
(6 early reservations) ==> bootmem [0000000000 - 0037fe2000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0001000000 - 00018bc708] TEXT DATA BSS ==> [0001000000 - 00018bc708]
#2 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
#3 [00018bd000 - 00018c4128] BRK ==> [00018bd000 - 00018c4128]
#4 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
#5 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00037fe2
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x00037fe2
On node 0 totalpages: 229249
free_area_init_node: node 0, pgdat c17fd05c, node_mem_map c18c5000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3967 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223490 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
Allocating PCI resources starting at 60000000 (gap: 60000000:9f800000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227457
Kernel command line:
PID hash table entries: 4096 (order: 12, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Memory: 899940k/917384k available (5206k kernel code, 16964k reserved, 3007k data, 408k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffe4000 - 0xfffff000 ( 108 kB)
vmalloc : 0xf87e2000 - 0xfffe2000 ( 120 MB)
lowmem : 0xc0000000 - 0xf7fe2000 ( 895 MB)
.init : 0xc1806000 - 0xc186c000 ( 408 kB)
.data : 0xc1515892 - 0xc18056fc (3007 kB)
.text : 0xc1000000 - 0xc1515892 (5206 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
Hierarchical RCU implementation.
NR_IRQS:16
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 1698.634 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Calibrating delay loop (skipped), value calculated using timer frequency.. 3397.26 BogoMIPS (lpj=6794536)
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
mce: CPU supports 5 MCE banks
CPU: Intel(R) Pentium(R) M processor 1.70GHz stepping 06
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090521
ACPI: setting ELCR to 0200 (from 0800)
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8d6, last bus=15
PCI: Using configuration type 1 for base access
bio: create slab at 0
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: Power Resource [PUBS] (on)
ACPI: ACPI Dock Station Driver: 3 docks/bays found
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 10 32bit mmio: [0xd0000000-0xdfffffff]
pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f]
pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f]
pci 0000:00:1d.2: reg 20 io port: [0x1840-0x185f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xc0000000-0xc00003ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4 GPIO
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.1: reg 20 io port: [0x1860-0x186f]
pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
pci 0000:00:1f.3: reg 20 io port: [0x1880-0x189f]
pci 0000:00:1f.5: reg 10 io port: [0x1c00-0x1cff]
pci 0000:00:1f.5: reg 14 io port: [0x18c0-0x18ff]
pci 0000:00:1f.5: reg 18 32bit mmio: [0xc0000c00-0xc0000dff]
pci 0000:00:1f.5: reg 1c 32bit mmio: [0xc0000800-0xc00008ff]
pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.5: PME# disabled
pci 0000:00:1f.6: reg 10 io port: [0x2400-0x24ff]
pci 0000:00:1f.6: reg 14 io port: [0x2000-0x207f]
pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.6: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xe0000000-0xe7ffffff]
pci 0000:01:00.0: reg 14 io port: [0x3000-0x30ff]
pci 0000:01:00.0: reg 18 32bit mmio: [0xc0100000-0xc010ffff]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:01.0: bridge io port: [0x3000-0x3fff]
pci 0000:00:01.0: bridge 32bit mmio: [0xc0100000-0xc01fffff]
pci 0000:00:01.0: bridge 32bit mmio pref: [0xe0000000-0xe7ffffff]
pci 0000:02:00.0: reg 10 32bit mmio: [0xb0000000-0xb0000fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:00.1: reg 10 32bit mmio: [0xb1000000-0xb1000fff]
pci 0000:02:00.1: supports D1 D2
pci 0000:02:00.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.1: PME# disabled
pci 0000:02:01.0: reg 10 32bit mmio: [0xc0240000-0xc025ffff]
pci 0000:02:01.0: reg 14 32bit mmio: [0xc0200000-0xc020ffff]
pci 0000:02:01.0: reg 18 io port: [0x8000-0x803f]
pci 0000:02:01.0: reg 30 32bit mmio: [0x000000-0x00ffff]
pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:02:02.0: reg 10 32bit mmio: [0xc0210000-0xc021ffff]
pci 0000:02:03.0: supports D1 D2
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0x4000-0x9fff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xc0200000-0xcfffffff]
pci 0000:00:1e.0: bridge 32bit mmio pref: [0xe8000000-0xefffffff]
pci 0000:09:01.0: reg 10 io port: [0x9020-0x9027]
pci 0000:09:01.0: reg 14 io port: [0x9014-0x9017]
pci 0000:09:01.0: reg 18 io port: [0x9018-0x901f]
pci 0000:09:01.0: reg 1c io port: [0x9010-0x9013]
pci 0000:09:01.0: reg 20 io port: [0x9000-0x900f]
pci 0000:09:01.0: supports D1 D2
pci 0000:09:02.0: reg 10 32bit mmio: [0xb2000000-0xb2000fff]
pci 0000:09:02.0: supports D1 D2
pci 0000:09:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:09:02.0: PME# disabled
pci 0000:09:02.1: reg 10 32bit mmio: [0xb3000000-0xb3000fff]
pci 0000:09:02.1: supports D1 D2
pci 0000:09:02.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:09:02.1: PME# disabled
pci 0000:02:03.0: transparent bridge
pci 0000:02:03.0: bridge io port: [0x00-0xfff]
pci 0000:02:03.0: bridge 32bit mmio: [0x000000-0x0fffff]
pci 0000:02:03.0: bridge 32bit mmio pref: [0x000000-0x0fffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1.DOCK._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
pci 0000:02:03.0: BAR 7: can't allocate resource
pci 0000:02:03.0: BAR 8: can't allocate resource
pci 0000:02:03.0: BAR 9: can't allocate resource
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
system 00:00: iomem range 0xc8000-0xcbfff could not be reserved
system 00:00: iomem range 0xcc000-0xcffff could not be reserved
system 00:00: iomem range 0xdc000-0xdffff could not be reserved
system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
system 00:00: iomem range 0xe8000-0xebfff could not be reserved
system 00:00: iomem range 0xec000-0xeffff could not be reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0x5fffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xffffffff could not be reserved
system 00:02: ioport range 0x1000-0x107f has been reserved
system 00:02: ioport range 0x1180-0x11bf has been reserved
system 00:02: ioport range 0x15e0-0x15ef has been reserved
system 00:02: ioport range 0x1600-0x162f has been reserved
system 00:02: ioport range 0x1632-0x167f has been reserved
system 00:02: ioport range 0x1630-0x1631 has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x3000-0x3fff
pci 0000:00:01.0: MEM window: 0xc0100000-0xc01fffff
pci 0000:00:01.0: PREFETCH window: 0xe0000000-0xe7ffffff
pci 0000:02:00.0: CardBus bridge, secondary bus 0000:10
pci 0000:02:00.0: IO window: 0x005000-0x0050ff
pci 0000:02:00.0: IO window: 0x005400-0x0054ff
pci 0000:02:00.0: PREFETCH window: 0xe8000000-0xebffffff
pci 0000:02:00.0: MEM window: 0xc4000000-0xc7ffffff
pci 0000:02:00.1: CardBus bridge, secondary bus 0000:14
pci 0000:02:00.1: IO window: 0x005800-0x0058ff
pci 0000:02:00.1: IO window: 0x005c00-0x005cff
pci 0000:02:00.1: PREFETCH window: 0xec000000-0xefffffff
pci 0000:02:00.1: MEM window: 0xc8000000-0xcbffffff
pci 0000:09:02.0: CardBus bridge, secondary bus 0000:0a
pci 0000:09:02.0: IO window: 0x004000-0x0040ff
pci 0000:09:02.0: IO window: 0x004400-0x0044ff
pci 0000:09:02.0: PREFETCH window: 0x6c000000-0x6fffffff
pci 0000:09:02.0: MEM window: 0x64000000-0x67ffffff
pci 0000:09:02.1: CardBus bridge, secondary bus 0000:0e
pci 0000:09:02.1: IO window: 0x004800-0x0048ff
pci 0000:09:02.1: IO window: 0x004c00-0x004cff
pci 0000:09:02.1: PREFETCH window: 0x70000000-0x73ffffff
pci 0000:09:02.1: MEM window: 0x68000000-0x6bffffff
pci 0000:02:03.0: PCI bridge, secondary bus 0000:09
pci 0000:02:03.0: IO window: 0x4000-0x4fff
pci 0000:02:03.0: MEM window: 0x64000000-0x6bffffff
pci 0000:02:03.0: PREFETCH window: 0x6c000000-0x73ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0: IO window: 0x4000-0x9fff
pci 0000:00:1e.0: MEM window: 0xc0200000-0xcfffffff
pci 0000:00:1e.0: PREFETCH window: 0xe8000000-0xefffffff
pci 0000:00:1e.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
pci 0000:02:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
pci 0000:02:00.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
pci 0000:09:02.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
pci 0000:09:02.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0x3000-0x3fff]
pci_bus 0000:01: resource 1 mem: [0xc0100000-0xc01fffff]
pci_bus 0000:01: resource 2 pref mem [0xe0000000-0xe7ffffff]
pci_bus 0000:02: resource 0 io: [0x4000-0x9fff]
pci_bus 0000:02: resource 1 mem: [0xc0200000-0xcfffffff]
pci_bus 0000:02: resource 2 pref mem [0xe8000000-0xefffffff]
pci_bus 0000:02: resource 3 io: [0x00-0xffff]
pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
pci_bus 0000:10: resource 0 io: [0x5000-0x50ff]
pci_bus 0000:10: resource 1 io: [0x5400-0x54ff]
pci_bus 0000:10: resource 2 pref mem [0xe8000000-0xebffffff]
pci_bus 0000:10: resource 3 mem: [0xc4000000-0xc7ffffff]
pci_bus 0000:14: resource 0 io: [0x5800-0x58ff]
pci_bus 0000:14: resource 1 io: [0x5c00-0x5cff]
pci_bus 0000:14: resource 2 pref mem [0xec000000-0xefffffff]
pci_bus 0000:14: resource 3 mem: [0xc8000000-0xcbffffff]
pci_bus 0000:09: resource 0 io: [0x4000-0x4fff]
pci_bus 0000:09: resource 1 mem: [0x64000000-0x6bffffff]
pci_bus 0000:09: resource 2 pref mem [0x6c000000-0x73ffffff]
pci_bus 0000:09: resource 3 io: [0x4000-0x9fff]
pci_bus 0000:09: resource 4 mem: [0xc0200000-0xcfffffff]
pci_bus 0000:09: resource 5 pref mem [0xe8000000-0xefffffff]
pci_bus 0000:09: resource 6 io: [0x00-0xffff]
pci_bus 0000:09: resource 7 mem: [0x000000-0xffffffff]
pci_bus 0000:0a: resource 0 io: [0x4000-0x40ff]
pci_bus 0000:0a: resource 1 io: [0x4400-0x44ff]
pci_bus 0000:0a: resource 2 pref mem [0x6c000000-0x6fffffff]
pci_bus 0000:0a: resource 3 mem: [0x64000000-0x67ffffff]
pci_bus 0000:0e: resource 0 io: [0x4800-0x48ff]
pci_bus 0000:0e: resource 1 io: [0x4c00-0x4cff]
pci_bus 0000:0e: resource 2 pref mem [0x70000000-0x73ffffff]
pci_bus 0000:0e: resource 3 mem: [0x68000000-0x6bffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
kvm: no hardware support
has_svm: not amd
kvm: no hardware support
Simple Boot Flag at 0x35 set to 0x1
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
HugeTLB registered 4 MB page size, pre-allocated 0 pages
fuse init (API version 7.12)
msgmni has been set to 1757
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pci 0000:01:00.0: Boot video device
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
decode_hpp: Could not get hotplug parameters. Use defaults
acpiphp: Slot [1] registered
acpiphp_ibm: ibm_acpiphp_init: acpi_walk_namespace failed
radeonfb 0000:01:00.0: power state changed by ACPI to D0
radeonfb 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
radeonfb: Retrieved PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=6) Memory=320.00 Mhz, System=210.00 MHz
radeonfb: PLL min 20000 max 35000
radeonfb: Monitor 1 type DFP found
radeonfb: EDID probed
radeonfb: Monitor 2 type CRT found
radeonfb: EDID probed
Display is GTF capable
radeonfb: Dynamic Clock Power Management enabled
radeonfb: IBM Thinkpad T42 detected, enabling workaround
Console: switching to colour frame buffer device 210x65
Switched to high resolution mode on CPU 0
radeonfb (0000:01:00.0): ATI Radeon 4e50 "NP"
uvesafb: failed to execute /sbin/v86d
uvesafb: make sure that the v86d helper is installed and executable
uvesafb: Getting VBE info block failed (eax=0x4f00, err=-2)
uvesafb: vbe_init() failed with -22
uvesafb: probe of uvesafb.0 failed with error -22
ACPI: AC Adapter [AC] (on-line)
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
ACPI: Sleep Button [SLPB]
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:02/device:03/input/input3
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
Marking TSC unstable due to TSC halts in idle
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor LNXCPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (48 C)
ACPI: Battery Slot [BAT0] (battery present)
intel_rng: FWH not detected
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 855PM Chipset
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.31.0 20080528 for 0000:01:00.0 on minor 0
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
serial 0000:00:1f.6: PCI INT B disabled
floppy0: no floppy controllers found
brd: module loaded
loop: module loaded
usbcore: registered new interface driver ub
Uniform Multi-Platform E-IDE driver
piix 0000:00:1f.1: IDE controller (0x8086:0x24ca rev 0x01)
pci 0000:00:1f.1: enabling device (0005 -> 0007)
pci 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867
ide1: BM-DMA at 0x1868-0x186f
Probing IDE interface ide0...
hda: FUJITSU MHT2060AH, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
Probing IDE interface ide1...
hdc: TOSHIBA MK4018GAP, ATA DISK drive
hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/100 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
cmd64x 0000:09:01.0: IDE controller (0x1095:0x0648 rev 0x01)
pci 0000:09:01.0: PCI INT A -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
cmd64x 0000:09:01.0: 100% native mode on irq 11
ide2: BM-DMA at 0x9000-0x9007
ide3: BM-DMA at 0x9008-0x900f
Probing IDE interface ide2...
hde: HL-DT-STCD-RW/DVD DRIVE GCC-4242N, ATAPI CD/DVD-ROM drive
hde: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hde: UDMA/33 mode selected
Probing IDE interface ide3...
ide2 at 0x9020-0x9027,0x9016 on irq 11
ide3 at 0x9018-0x901f,0x9012 on irq 11
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
ide-gd driver 1.18
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 >
hdc: max request size: 128KiB
hdc: 78140160 sectors (40007 MB), CHS=65535/16/63
hdc: cache flushes supported
hdc: hdc2 < hdc5 hdc6 hdc7 hdc8 hdc9 hdc10 >
ide-cd driver 5.00
ide-cd: hde: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
SCSI Media Changer driver v0.25
Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e1000 0000:02:01.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:0d:60:fa:7f:03
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
Intel(R) Gigabit Ethernet Network Driver - version 1.3.16-k2
Copyright (c) 2007-2009 Intel Corporation.
Intel(R) Virtual Function Network Driver - version 1.0.0-k0
Copyright (c) 2009 Intel Corporation.
pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
arlan: No Arlan devices found
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver zaurus
orinoco 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_plx 0.15 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson.dropbear.id.au>, Daniel Barlow <dan@telent.net>)
orinoco_pci 0.15 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson.dropbear.id.au> & Jean Tourrilhes <jt@hpl.hp.com>)
orinoco_tmd 0.15 (Joerg Dorchain <joerg@dorchain.net>)
spectrum_cs 0.15 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson.dropbear.id.au>, et al)
airo(): Probing for PCI adapters
airo(): Finished probing for PCI adapters
Loaded prism54 driver, version 1.2
yenta_cardbus 0000:02:00.0: CardBus bridge found [1014:0552]
yenta_cardbus 0000:02:00.0: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:02:00.0: Routing CardBus interrupts to PCI
yenta_cardbus 0000:02:00.0: TI: mfunc 0x01d21b22, devctl 0x64
yenta_cardbus 0000:02:00.0: ISA IRQ mask 0x04f8, PCI irq 11
yenta_cardbus 0000:02:00.0: Socket status: 30000086
pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #0f to #13
yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x9fff
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x4000-0x9fff: clean.
yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
yenta_cardbus 0000:02:00.1: CardBus bridge found [1014:0552]
yenta_cardbus 0000:02:00.1: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:02:00.1: Routing CardBus interrupts to PCI
yenta_cardbus 0000:02:00.1: TI: mfunc 0x01d21b22, devctl 0x64
yenta_cardbus 0000:02:00.1: ISA IRQ mask 0x04f8, PCI irq 11
yenta_cardbus 0000:02:00.1: Socket status: 30000086
pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #13 to #17
yenta_cardbus 0000:02:00.1: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x9fff
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x4000-0x9fff: clean.
yenta_cardbus 0000:02:00.1: pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
yenta_cardbus 0000:02:00.1: pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
yenta_cardbus 0000:09:02.0: CardBus bridge found [1014:0148]
yenta_cardbus 0000:09:02.0: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:09:02.0: Routing CardBus interrupts to PCI
yenta_cardbus 0000:09:02.0: TI: mfunc 0x00001002, devctl 0x66
yenta_cardbus 0000:09:02.0: ISA IRQ mask 0x04f8, PCI irq 11
yenta_cardbus 0000:09:02.0: Socket status: 30000006
yenta_cardbus 0000:09:02.0: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
pcmcia_socket pcmcia_socket2: cs: IO port probe 0x4000-0x4fff: clean.
yenta_cardbus 0000:09:02.0: pcmcia: parent PCI bridge Memory window: 0x64000000 - 0x6bffffff
yenta_cardbus 0000:09:02.0: pcmcia: parent PCI bridge Memory window: 0x6c000000 - 0x73ffffff
yenta_cardbus 0000:09:02.0: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x9fff
yenta_cardbus 0000:09:02.0: pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
yenta_cardbus 0000:09:02.0: pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
yenta_cardbus 0000:09:02.1: CardBus bridge found [1014:0148]
yenta_cardbus 0000:09:02.1: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:09:02.1: Routing CardBus interrupts to PCI
yenta_cardbus 0000:09:02.1: TI: mfunc 0x00001002, devctl 0x66
yenta_cardbus 0000:09:02.1: ISA IRQ mask 0x04f8, PCI irq 11
yenta_cardbus 0000:09:02.1: Socket status: 30000006
yenta_cardbus 0000:09:02.1: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
pcmcia_socket pcmcia_socket3: cs: IO port probe 0x4000-0x4fff: clean.
yenta_cardbus 0000:09:02.1: pcmcia: parent PCI bridge Memory window: 0x64000000 - 0x6bffffff
yenta_cardbus 0000:09:02.1: pcmcia: parent PCI bridge Memory window: 0x6c000000 - 0x73ffffff
yenta_cardbus 0000:09:02.1: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x9fff
yenta_cardbus 0000:09:02.1: pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
yenta_cardbus 0000:09:02.1: pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31.4 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31.4 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.31.4 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-usbat
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
belkin_sa: v1.2:USB Belkin Serial converter driver
USB Serial support registered for Reiner SCT Cyberjack USB card reader
usbcore: registered new interface driver cyberjack
cyberjack: v1.01 Matthias Bruestle
cyberjack: REINER SCT cyberJack pinpad/e-com USB Chipcard Reader Driver
USB Serial support registered for Digi 2 port USB adapter
USB Serial support registered for Digi 4 port USB adapter
usbcore: registered new interface driver digi_acceleport
digi_acceleport: v1.80.1.2:Digi AccelePort USB-2/USB-4 Serial Converter driver
USB Serial support registered for Edgeport 2 port adapter
USB Serial support registered for Edgeport 4 port adapter
USB Serial support registered for Edgeport 8 port adapter
USB Serial support registered for EPiC device
usbcore: registered new interface driver io_edgeport
io_edgeport: v2.7:Edgeport USB Serial Driver
USB Serial support registered for Edgeport TI 1 port adapter
USB Serial support registered for Edgeport TI 2 port adapter
usbcore: registered new interface driver io_ti
io_ti: v0.7mode043006:Edgeport USB Serial Driver
USB Serial support registered for empeg
usbcore: registered new interface driver empeg
empeg: v1.2:USB Empeg Mark I/II Driver
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
USB Serial support registered for PocketPC PDA
usbcore: registered new interface driver ipaq
ipaq: v0.5:USB PocketPC PDA driver
usb 1-1: new full speed USB device using uhci_hcd and address 2
USB Serial support registered for IR Dongle
usbcore: registered new interface driver ir-usb
ir_usb: v0.4:USB IR Dongle driver
USB Serial support registered for Keyspan PDA
USB Serial support registered for Keyspan PDA - (prerenumeration)
USB Serial support registered for Xircom / Entregra PGS - (prerenumeration)
usbcore: registered new interface driver keyspan_pda
keyspan_pda: v1.1:USB Keyspan PDA Converter driver
USB Serial support registered for KL5KUSB105D / PalmConnect
usbcore: registered new interface driver kl5kusb105d
kl5kusb105: v0.3a:KLSI KL5KUSB105 chipset USB->Serial Converter driver
USB Serial support registered for KOBIL USB smart card terminal
usbcore: registered new interface driver kobil
kobil_sct: 21/05/2004:KOBIL USB Smart Card Terminal Driver (experimental)
USB Serial support registered for MCT U232
usbcore: registered new interface driver mct_u232
mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver
USB Serial support registered for ZyXEL - omni.net lcd plus usb
usbcore: registered new interface driver omninet
omninet: v1.1:USB ZyXEL omni.net LCD PLUS Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
USB Serial support registered for Handspring Visor / Palm OS
USB Serial support registered for Sony Clie 3.5
USB Serial support registered for Sony Clie 5.0
usbcore: registered new interface driver visor
visor: USB HandSpring Visor / Palm OS driver
usbcore: registered new interface driver emi26 - firmware loader
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram
usb 1-1: New USB device found, idVendor=04b3, idProduct=4481
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: configuration #1 chosen from 1 choice
Driver for 1-wire Dallas network protocol.
hub 1-1:1.0: USB hub found
hdaps: inverting axis (0) readings.
hdaps: IBM ThinkPad T42 detected.
hub 1-1:1.0: 4 ports detected
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
hdaps: initial latch check good (0x01).
hdaps: device successfully initialized.
input: hdaps as /devices/platform/hdaps/input/input5
hdaps: driver successfully loaded.
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: multipath personality registered for level -4
md: faulty personality registered for level -5
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.1.0 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
Intel ICH 0000:00:1f.5: setting latency timer to 64
usb 1-1.3: new full speed USB device using uhci_hcd and address 3
IBM TrackPoint firmware: 0x0e, buttons: 3/3
usb 1-1.3: New USB device found, idVendor=05e3, idProduct=0608
usb 1-1.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1.3: Product: USB2.0 Hub
usb 1-1.3: configuration #1 chosen from 1 choice
input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input6
hub 1-1.3:1.0: USB hub found
hub 1-1.3:1.0: 4 ports detected
usb 1-1.3.4: new low speed USB device using uhci_hcd and address 4
usb 1-1.3.4: New USB device found, idVendor=046d, idProduct=c03d
usb 1-1.3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.3.4: Product: USB-PS/2 Optical Mouse
usb 1-1.3.4: Manufacturer: Logitech
usb 1-1.3.4: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.0/input/input7
generic-usb 0003:046D:C03D.0001: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1.3.4/input0
intel8x0_measure_ac97_clock: measured 55455 usecs (2672 samples)
intel8x0: clocking to 48000
usbcore: registered new interface driver snd-usb-audio
usbcore: registered new interface driver snd-usb-usx2y
ALSA device list:
#0: Intel 82801DB-ICH4 with AD1981B at irq 11
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (14334 buckets, 57336 max)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP westwood registered
TCP vegas registered
TCP veno registered
TCP illinois registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
tunl0: Disabled Privacy Extensions
Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
CCID: Activated CCID 2 (TCP-like)
CCID: Activated CCID 3 (TCP-Friendly Rate Control)
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
lib80211_crypt: registered algorithm 'WEP'
lib80211_crypt: registered algorithm 'CCMP'
lib80211_crypt: registered algorithm 'TKIP'
TIPC: Activated (version 1.6.4 compiled Oct 19 2009 15:35:24)
NET: Registered protocol family 30
TIPC: Started in single node mode
Installing 9P2000 support
P-state transition latency capped at 20 uS
PM: Checking image partition hda11
PM: Resume from disk failed.
rtc_cmos 00:06: setting system clock to 2009-10-19 22:04:02 UTC (1255989842)
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly on device 3:5.
Freeing unused kernel memory: 408k freed
Write protecting the kernel text: 5208k
Write protecting the kernel read-only data: 2580k
Clocksource tsc unstable (delta = -271773305 ns)
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x4ff: excluding 0x4d0-0x4d7
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x800-0x8ff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x4ff: excluding 0x4d0-0x4d7
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x800-0x8ff: clean.
pcmcia_socket pcmcia_socket2: cs: IO port probe 0x100-0x4ff: excluding 0x4d0-0x4d7
pcmcia_socket pcmcia_socket3: cs: IO port probe 0x100-0x4ff: excluding 0x4d0-0x4d7
pcmcia_socket pcmcia_socket3: cs: IO port probe 0x800-0x8ff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcff: clean.
pcmcia_socket pcmcia_socket2: cs: IO port probe 0x800-0x8ff: clean.
pcmcia_socket pcmcia_socket2: cs: IO port probe 0xc00-0xcff: clean.
pcmcia_socket pcmcia_socket3: cs: IO port probe 0xc00-0xcff: clean.
pcmcia_socket pcmcia_socket3: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket2: cs: IO port probe 0xa00-0xaff: clean.
Adding 979924k swap on /dev/hda11. Priority:0 extents:1 across:979924k
EXT3 FS on hda5, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda12, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1048568k swap on /dev/mapper/MaraUltraBay-UltraBaySwap. Priority:0 extents:1 across:1048568k
warning: `miredo' uses 32-bit capabilities (legacy support in use)
teredo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-13, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-16, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS on dm-14, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS on dm-8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-12, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-15, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
agpgart-intel 0000:00:00.0: AGP 2.0 bridge
agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
radeonfb 0000:01:00.0: putting AGP V2 device into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] Num pipes: 1
[drm] writeback test succeeded in 1 usecs
...
</pre>